Audi A4, S4

since 2000 of release

Repair and car operation


Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
- Current leaving and service
   Specifications
   Indicator of term of approach of maintenance
   Schedule of routine maintenance
   General information on control
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels. Rotation and replacement of wheels
   Replacement of impellent oil and oil filter
   Checks of brake system. Adjustment of the parking brake
   Check of fuel system
   Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
   Check of a condition of ridge belts of a streaming drive of auxiliary units
   Check of functioning of system of cooling and frost resistance of cooling liquid
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil of automatic transmission
   Visual control of a box of gear shifting and the main transfer on leaks, check of level and oil addition
   Condition check suspension bracket and steering component
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Check of central air of air
   Greasing of limiters of doors, cylinders of locks, hook of a cowl, movable panel of the hatch of a roof
   Visual control of a seat belt and safety cushion block
   Check of operability of headlights and horn
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of the battery of emergency supply of Telematik system
   Replacement of an element of the filter of air of salon / coal filter of purification of air
   Replacement of brake liquid
   Check and replacement of spark plugs. Check of a condition of high-voltage wires
   Replacement of an element of the air filter of the engine
   Replacement of the fuel filter
   Check of a condition and tension of a gear belt
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

f6be02a9

Check and replacement of spark plugs. Check of a condition of high-voltage wires

Address also to the Spark plug Section.

Spark plugs replace only on cold or slightly warm engine. If candles are turned out on the hot engine, the carving of a head of the cylinders executed from light metal can be broken.

Before the beginning of work prepare all necessary tools. Some producers of spark plugs deliver special tools for measurement of a candle gap.

    Candle key on 16 mm, for example, HAZET 4766-1 or AUDI-3122В. If necessary, AUDI T40039 stripper for ignition coils. Depending on number of cylinders of the engine necessary quantity of spark plugs. Applied spark plugs are listed in Specifications.

The best way of replacement of spark plugs is preliminary purchase of new candles, adjustment of their gap and replacement of each candle in turn. Upon purchase of candles it is very important to choose those candles which are intended for the engine of your car. Information on them is provided in Specifications.

Having near at hand new candles, let's to the engine cool down completely before the beginning of removal of the old. During this time it is possible to examine new candles on existence in them of defects and to check candle gaps.

Security measures: Do not concern the parts being under a high voltage. The persons having a warm stimulator, should not carry out any works with electronic system of ignition.

Removal

 PERFORMANCE ORDER

    Switch off ignition.
    Remove the top cover of the engine, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.
    Disunite sockets (1) spark plugs (an illustration - the Engine of 1.6 l).
    Disunite connecting tips (1) coils of ignition (an illustration - the Engine of 1.6 l).
    Disconnect rod coils of ignition from spark plugs, for example, AUDI T40039 stripper.

Stripper Т40039 establish surely on the most top, thick edge (an arrow on an accompanying illustration) coils of ignition and pull up. At installation on the bottom edge it can be damaged.

Engine of 2.0 l

 PERFORMANCE ORDER

    Turn out bolts (1).
    Disunite sockets (2) coils of ignition.
    Remove strezhnevy coils of ignition (3), as on the engine of 1.8 l, from spark plugs, for example, stripper Т40039.

Engine of 3.0 l

 PERFORMANCE ORDER

    Remove the top part of the air filter, address to the Section Removal and installation of the air filter. Disconnect a broad tank of cooling liquid from the holder and take him aside with the attached hoses.
    Turn out screws (1). On an accompanying illustration the right number of cylinders is shown.
    Disunite sockets (2) coils of ignition (3). Disconnect rod coils of ignition (3), as at the engine of 1.8 l, from spark plugs, for example, by means of stripper Т40039.

Engine of 4.2 l

 PERFORMANCE ORDER

    Remove the air filter. Remove the left top cover of an impellent compartment. Disconnect a broad tank of cooling liquid from the holder and take him aside with the attached hoses.
    Turn out screws (1). On an accompanying illustration the right number of cylinders is shown.
    Disunite sockets (2) coils of ignition. Disconnect rod coils of ignition (3), as at the engine of 1.8 l, from spark plugs, for example, by means of stripper Т40039.

All engines

 PERFORMANCE ORDER

    Turn out spark plugs by means of the corresponding candle key, for example, HAZET 4766-1 or AUDI. Thus watch that the candle key did not warp. Otherwise it can lead to destruction of a ceramic insulator.

Check

 PERFORMANCE ORDER

    Compare the taken-out candle with shown in pictures in the Head of System of electric equipment of the engine, it will give you useful information about the general condition of the engine. Check shchupy interelectrode distance. On illustrations the candle with one electrode of weight is shown. Demanded value of a gap is given in Specifications.

At new candles the interelectrode distance is, as a rule, established correctly.

    For distance installation between contacts turn in the corresponding electrode of weight. For this purpose knock on it sideways. At a podgibaniye обоприте a small screw-driver about carving edge. Do not lean at all about the central electrode as it can be damaged. Put a little medsoderzhashchy anti-taking structure on a carving of a new candle.

Installation

Establish a candle in a head of cylinders and screw it fingers against the stop, then tighten by means of a head of a candle key.

In order to avoid possibility of a vvinchivaniye of a candle not on a carving put on its shaft a small piece of a rubber hose or a plastic tube. The flexible tube will work as universal - the kardanny hinge, providing candle alignment in relation to a candle nest and in case the candle starts to warp, the hose will slip on it, without giving possibility to strip a thread.

If it is possible, use for a candle tightening a dinamometrichesky key to be sure that it is established correctly. The effort of a tightening of candles is given in Specifications. If the dinamometrichesky key available is not present, tighten new candles on a corner 90 °, candles being in the use - on 15 °. The too strongly tightened candles at a reversing can damage a carving in a head of cylinders. In this case repair of a carving is made by means of UTC or Heli-Coil inserts.

 PERFORMANCE ORDER

    Further installation is carried out in sequence, return to removal. All engines, except 1.6 l: Establish coils of ignition by easy turn. They should be fixed distinctly. Engine of 1.6 l: Join sockets. Then check reliability of fastening of wires and sockets. Establish into place the top cover of the engine, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.