Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
- Current leaving and service
   Specifications
   Indicator of term of approach of maintenance
   Schedule of routine maintenance
   General information on control
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels. Rotation and replacement of wheels
   Replacement of impellent oil and oil filter
   Checks of brake system. Adjustment of the parking brake
   Check of fuel system
   Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
   Check of a condition of ridge belts of a streaming drive of auxiliary units
   Check of functioning of system of cooling and frost resistance of cooling liquid
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil of automatic transmission
   Visual control of a box of gear shifting and the main transfer on leaks, check of level and oil addition
   Condition check suspension bracket and steering component
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Check of central air of air
   Greasing of limiters of doors, cylinders of locks, hook of a cowl, movable panel of the hatch of a roof
   Visual control of a seat belt and safety cushion block
   Check of operability of headlights and horn
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of the battery of emergency supply of Telematik system
   Replacement of an element of the filter of air of salon / coal filter of purification of air
   Replacement of brake liquid
   Check and replacement of spark plugs. Check of a condition of high-voltage wires
   Replacement of an element of the air filter of the engine
   Replacement of the fuel filter
   Check of a condition and tension of a gear belt
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


f6be02a9

Replacement of brake liquid

It will be necessary for carrying out work for you:

    Cap key for an otvorachivaniye of the union of removal of air. Transparent plastic hose in internal diameter of 6 mm and capacity for collecting brake liquid. Necessary amount of the brake liquid corresponding to the specification.

The brake liquid which was in the use repeatedly do not apply. Old brake liquid is much more dark the fresh. It allows to distinguish them easily.

Brake liquid through a time of brake hoses and a ventilating opening of the tank absorbs moisture. Thereof the temperature of boiling of liquid in use decreases. At big load of brakes it can lead even to steam formation that reduces efficiency of action of brakes.

Brake liquid owes each 2 years, it is desirable in the spring, to be replaced with the new. At frequent movement in the mountain district, it is necessary to replace liquid more often.

On HUNDRED air from brake system, as a rule, is removed on the special device. However it is possible to do it and without use of the specified device. Thus the brake system is pumped over by a brake pedal. For this purpose participation of the assistant is required.

If in the course of air removal from brake system liquid level sharply decreases, occurs подсос the air getting to the pump ABS. In this case removal of air is necessary for making on HUNDRED with use of the special device. At replacement of any brake hose it is also necessary to remove air from system on HUNDRED. While it is not made, to use the car it is impossible.

Sequence of removal of air:

    Support the back right Support the back left Support the forward right Support the forward left

Pay attention to remarks according to safety measures at the treatment of brake liquid, address to the Section air Removal from brake system.

Cover (1) tank of brake liquid and tube under a carving stopper (shooter) for removal of brake liquid by means of a rubber pear

 PERFORMANCE ORDER

    By means of a pear remove from the tank brake liquid, having left at the bottom of the tank a liquid layer in thickness about 10 mm. Do not delete from the tank all liquid, differently air will get to brake system.
    Fill the compensatory tank with new brake liquid to a label the MOVE.
    Carefully, not to curtail, open the union of removal of air. It is recommended in 2 hours prior to the beginning of removal of air to process the union means for rust removal. If the union does not open, on air removal from brake system it is necessary to charge operation to a workshop.

    On the right back support of the disk wheel brake mechanism put on the union of removal of air a pure transparent hose and insert it into a suitable vessel. Ask the assistant to squeeze out repeatedly a brake pedal while antipressure to pressing of a pedal does not become notable. Press a pedal and open the union of removal of air. The union close after the brake pedal will rest against a body floor. Clean a foot from a pedal. Repeating this process, pump out about 400-500 ml of old brake liquid. Close the union of removal of air and fill in in the compensatory tank new brake liquid. In the same way pump out old brake liquid from other supports or wheel brake cylinders, observing the sequence specified above.

Merged brake liquid in any case should be pure and without air vials. From each brake support it is necessary to pump out about 400-500 cm of the 3rd old brake liquid.

    Old brake liquid hand over on special point on reception of the fulfilled combustive-lubricating materials. Press a brake pedal and check a free wheeling. It should not exceed 1/3 courses of a pedal. Fill in brake liquid in the tank to earlier existing level. Screw on the tank a stopper. Inspect reliability:
      Whether brake pipelines and hoses are fixed? Whether there are brake hoses in holders? Whether unions of removal of air are tightened? Whether liquid enough is filled in in system?
    On the working engine check tightness of system. For this purpose about 10 times press a brake pedal with effort of 200-300 N (there correspond 20-30 kg). The pedal of a brake should not leave back. Check on tightness all connections. In summary check action of brakes on the road with not heavy traffic of transport. For this purpose it is necessary to make not less than one strong braking, having checked ABS action (a sign of work of ABS the pulsation of a pedal of a brake is when braking).

Watch transport going following of your car. The effect of action of ABS is best of all shown on an unpaved road.

It is not necessary to pour out brake liquid together with a household waste or somewhere in other place.