Audi A4, S4

since 2000 of release

Repair and car operation


Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
- Current leaving and service
   Specifications
   Indicator of term of approach of maintenance
   Schedule of routine maintenance
   General information on control
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels. Rotation and replacement of wheels
   Replacement of impellent oil and oil filter
   Checks of brake system. Adjustment of the parking brake
   Check of fuel system
   Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
   Check of a condition of ridge belts of a streaming drive of auxiliary units
   Check of functioning of system of cooling and frost resistance of cooling liquid
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil of automatic transmission
   Visual control of a box of gear shifting and the main transfer on leaks, check of level and oil addition
   Condition check suspension bracket and steering component
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Check of central air of air
   Greasing of limiters of doors, cylinders of locks, hook of a cowl, movable panel of the hatch of a roof
   Visual control of a seat belt and safety cushion block
   Check of operability of headlights and horn
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of the battery of emergency supply of Telematik system
   Replacement of an element of the filter of air of salon / coal filter of purification of air
   Replacement of brake liquid
   Check and replacement of spark plugs. Check of a condition of high-voltage wires
   Replacement of an element of the air filter of the engine
   Replacement of the fuel filter
   Check of a condition and tension of a gear belt
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

f6be02a9

Visual control of a box of gear shifting and the main transfer on leaks, check of level and oil addition

For search of places of leaks:

 PERFORMANCE ORDER

    Diesel engine: remove the bottom cover of the engine, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher. Clear the transmission case a cold cleaner. Strew possible places of leaks with lime or a talc powder. Pass on the car. That oil became liquid, pass on the high-speed route distance about 30 km.

Operation of lifting and car installation on supports is connected with danger! Therefore before carrying out operation familiarize with Poddomkrachivaniye's Section and towage.

    Lift and establish the car on supports. Shine with a lamp a transmission and check places of leaks. At once eliminate leaks. Diesel engine: Establish the bottom cover of the engine, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.

Check of level and oil addition

Special tool:

    Viewing hole or jack with supports. For a stopper otvorachivaniye for system filling with oil depending on execution:
      six-sided face key on 10 mm, for example, HAZET 985-10; many-sided face key on 16 mm, for example, HAZET 2567-16 or AUDI 3357. The thin wire, which end in length of 1 cm it is unbent on 90 °, for measurement of level of oil.

 PERFORMANCE ORDER

    Establish the car over a viewing hole or lift horizontally on supports. Remove the bottom cover of the engine, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher. The stopper for a flood of oil is on a check point before the left power shaft and can be closed by the heat-shielding screen of a shaft. In this case it is necessary to disconnect the heat-shielding screen.
    Turn out a stopper for an oil flood a face key for an internal shestigrannik on 10 mm or a key under an internal polyhedron 3357.
    Models with a forward drive and a check point 012/01W: To control of level of oil apply the index of own manufacturing described above with the unbent end. For level control the index keep in an opening horizontally, the unbent end should look down. Take out the index and check oil level according to the index. Oil level correct if it is on 7 mm below an opening.
    1 — Oil in a check point
    2 — the Index of level of oil of own manufacturing
    3 — Carter of a check point
    Models with a 5-step full drive (01А), and also with 5-and a 6-step forward drive (01Е): Level of oil should reach the bottom edge of an opening under a carving stopper. Models with a 6-step full drive (01Е): Level of oil should be on 1 ± 1 mm below an opening under a carving stopper.

If oil level too low, check a box on tightness, if necessary, repair (work HUNDRED). It is not enough to fill in oil only. It is necessary to observe the established level of oil! By no means it is impossible to pour oil.

    If a check point it is tight, fill in oil. Tighten a stopper the moment specified in Specifications. Fix the heat-shielding screen on a check point if he acted in film. Establish into place a cover of an impellent compartment, address to the Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.

Differential of a back axis, quattro model

Check of level of oil of differential is made at a stopper otvorachivaniye for filling with oil (shooter). Level of oil should reach the bottom edge of a carving opening.

Tighten a stopper the moment specified in Specifications.