Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures at carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   + External equipment
   - Salon equipment
      Remarks on work with the salon and security measure equipment
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of the parking brake
      Removal and installation of a cover of the lever of switching of transfers/selector
      Removal and ashtray installation
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and cover installation on a control panel
      Removal and pocket installation from the driver
      Removal and installation of a ware box
      Removal and installation of an antisolar peak
      Removal and installation of facing are resistant And
      Removal and installation of the top facing of a rack In
      Removal and installation of the bottom facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Versatile person)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment


f6be02a9

Removal and installation of facings (Versatile person)

Rack With

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a safety cushion surely observe security measures at the address with a safety cushion, address to the Section General information and security measures.

    To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive cables of the storage battery. Instructions are provided in the Section Replacement of the storage battery. Remove a lateral pillow of a back seat, address to the Section Removal and installation of a back seat. Remove lateral facing of a luggage carrier, address to appropriate section. Remove facing over a back door. Weaken screws of fastening of a safety cushion of the head in a back part. Remove directing for a back belt, address to the Section Removal and installation of a back seat belt.
    Turn out screws (3), disconnect facing (1) at a spring clip (2) and remove.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal. Thus fix a head safety cushion new screws. Put a door sealant over facing.

During connection of the storage battery in salon there should not be people.

    Remove an insulating tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery battery room.

Observe indications of the Section Replacement of the storage battery.

Facing over a back door

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a safety cushion surely observe security measures at the address with a safety cushion, address to the Section General information and security measures.

    To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive cables of the storage battery. Instructions are provided in the Section Replacement of the storage battery. Disconnect facing behind a rack And. Remove facing of a rack by D.
    Press down the handle (5) and cast away down a screw (4) cover. For this purpose enter into a groove (7) thin wire and open a cover.
    Turn out screws (3). Turn out the screw (1). Turn out the screw (7) for what displace back a level in an eye for a dividing grid. Disconnect facing (2) at a spring clip (6) and remove.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal, thus the screw (7) tighten the moment 9Нм.

During connection of the storage battery in salon there should not be people.

    Remove an insulating tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery battery room.

Observe indications of the Section Replacement of the storage battery.

Rack of D

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a safety cushion surely observe security measures at the address with a safety cushion, address to the Section General information and security measures.

    To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive cables of the storage battery. Instructions are provided in the Section Replacement of the storage battery. Remove closing level of a roof, address to the Section Removal and installation of facings (Sedan). Disconnect a back edge of lateral facing of a cargo compartment, address to appropriate section.
    Turn out the screw (3) for what displace back a level in an eye for a dividing grid.
    Disconnect facing (1) at two spring clips (2) and take out up from lateral facing of a cargo compartment. Take out facing of a rack by D (1) back from facing (4) over a door. Weaken in a back part screws of fastening of a safety cushion of the head. Turn out screws (6) and remove facing (5) over a back window.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence. return to removal. Thus fix a head safety cushion new screws. Put a sealant of a cover of a back over facing.

During connection of the storage battery in salon there should not be people.

    Remove an insulating tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery battery room.

Observe indications of the Section Replacement of the storage battery.

Closing level of a roof

Removal

 PERFORMANCE ORDER

    Disconnect closing level of a roof (1) at four spring clips (2) and remove.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal. Put a sealant of a cover of a back over a closing level of a roof.

Lateral facing of a cargo compartment

Removal

 PERFORMANCE ORDER

    Lateral facing right: Disconnect a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

    Remove a lateral pillow of a back seat, address to the Section Removal and installation of a back seat. Release a floor of a cargo room and take out. Remove an overlay of a cargo compartment, see below.
    Turn out screws (4) fastenings of an eye for luggage (5).
    Turn out the screw (3) and disconnect lateral facing (2) at spring clips (1). Right lateral facing: Disunite the socket socket. Take out lateral facing.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal. Right lateral facing: Attach a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

Overlay of the lock of a cargo compartment

Removal

 PERFORMANCE ORDER

    Open a back door.
    Turn out 4 screws (1) and carefully disconnect an overlay of the lock (2) from a compartment edge at lock fingers (the shooter on an accompanying illustration). Thus displace a plastic wedge under a slip and each finger remove separately.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal.