Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures at carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
+ External equipment
- Salon equipment
Remarks on work with the salon and security measure equipment
Removal and installation of spring clips
Removal and installation of the central console
Removal and installation of the holder of drinks
Removal and installation of facing of the lever of the parking brake
Removal and installation of a cover of the lever of switching of transfers/selector
Removal and ashtray installation
Removal and installation of the central armrest
Removal and installation of an internal mirror
Removal and cover installation on a control panel
Removal and pocket installation from the driver
Removal and installation of a ware box
Removal and installation of an antisolar peak
Removal and installation of facing are resistant And
Removal and installation of the top facing of a rack In
Removal and installation of the bottom facing of a rack In
Removal and installation of a forward overlay of a threshold
Removal and installation of facings (Sedan)
Removal and installation of facings (Versatile person)
Removal and installation of a forward seat
Removal and installation of a back seat
Removal and installation of a forward seat belt
Removal and installation of a back seat belt
+ Onboard electric equipment
|
Removal and installation of facings (Sedan) Rack With
Removal
|
|
|
|
To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive cables of the storage battery. Instructions are provided in the Section Replacement of the storage battery.
Remove closing level of a roof, see below.
|
Turn out screws (2).
|
|
Remove lateral pillows of a back seat, address to the Section Removal and installation of a back seat.
Take out a clip (3) under a lateral pillow.
Disconnect the lateral shelf and raise it, address to appropriate section.
Disconnect rack facing With (1) at a spring clip (4) and remove it.
|
|
Installation
|
|
Raise the shelf and insert rack facing With into grooves on a regiment.
Further installation is carried out in sequence, return to removal. Thus replace being self-stopped screws (2) with the new.
|
|
During connection of the storage battery in salon there should not be people. |
Remove an insulating tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery battery room.
|
|
Rack of D
Removal
|
|
|
|
To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive cables of the storage battery. Instructions are provided in the Section Replacement of the storage battery.
Remove facing of a rack by D, address to appropriate section.
|
Press down the handle (5) and cast away down a screw (4) cover. For this purpose enter into a groove (7) thin wire and open a cover.
|
|
Turn out screws (6).
Turn out the screw (3) and disconnect behind facing of a rack And, address to appropriate section.
Extend facing (1) under facing of a rack of Century.
Disconnect facing of a rack by D (1) at spring clips (2) and extend from the shelf.
|
|
Installation
|
|
Enter into the shelf facing behind a rack of D.
Insert a hook (7) into shlitsa at facing of a rack of Page.
Fix facing of a rack by D at spring clips (2).
Insert forward facing under facing of a rack of Century.
Check, that the clip and a hook of the adapter of a safety cushion were reliably fixed.
Screw the screw (3) and fix facing behind a rack And.
Fix the handle new being self-stopped screws (6). Put into place a screw cover.
Put over facing a door sealant.
Establish into place a level of the lock of a roof, see below.
|
|
During connection of the storage battery in salon there should not be people. |
Remove an insulating tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery battery room.
|
|
Closing level of a roof
Removal
|
|
Disconnect closing level of a roof (1) at spring clips (2) of grooves (3) and remove.
|
|
|
Installation
|
|
Installation is carried out in sequence, return to removal.
|
|
Back entrance level
Removal
Installation
|
|
Installation is carried out in sequence, return to removal.
|
|
Shelf
Removal
|
|
Depending on the equipment: Cast away a back of a back seat or remove, address to the Section Removal and installation of a back seat.
Disconnect from the shelf rack facing With at the left and on the right.
Remove the left and right lateral pillows of a back seat, address to the Section Removal and installation of a back seat.
Not leaning back back seat: Disconnect below the central seat belt.
|
Remove from the shelf by means of a plastic wedge a lattice of a loudspeaker (3).
|
|
Depending on the equipment turn out 3 or 4 screws (4).
Turn out from below 3 screws of fastening solar a shtorok in a luggage carrier and extend a curtain forward.
Pull the shelf (1) forward (shooter), disconnect at an edge (2) and take out upward.
|
|
Installation
|
|
Installation is carried out in sequence, return to removal.
|
|
Lateral facing of a luggage carrier
Removal
|
|
Open a luggage carrier and take out a floor cover.
Remove facing of overlapping of a back.
Remove a back of a back seat, address to the Section Removal and installation of a back seat.
Turn out bolts of fastening of eyes of a luggage carrier.
Disconnect lateral facing at four spring clips above and behind and remove up. If it is necessary, previously open in facing a cover боковины.
|
|
Installation
|
|
Installation is carried out in sequence, return to removal. Thus a sealant of a door put over facing.
|
|
Back overlapping
Removal
|
|
Open a luggage carrier and take out a floor cover.
|
Unscrew 2 nuts (2), if necessary, take out a spare wheel.
|
|
Disunite the socket of a lamp of illumination of a luggage carrier.
Disconnect facing of overlapping of a back (1) in four spring clips (3) and remove overlapping.
|
|
Installation
|
|
Installation is carried out in sequence, return to removal.
|
|
|
|
