Audi A4, S4

since 2000 of release

Repair and car operation


Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures at carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and window regulator installation
      Removal and installation of the electric motor of a drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and trunk lid adjustment
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + salon Equipment
+ Onboard electric equipment

f6be02a9

Removal and cowl installation/adjustment

1 — the Cowl
2 — the Loop
3 — Two bolts, 21Нм

4 — Two nuts, 21Нм
5 — the Gas-filled emphasis

Removal

 PERFORMANCE ORDER

    Open a cowl Disconnect a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

    Disconnect a hose and disunite the socket of a jet of a stekloomyvatel. For possibility of the subsequent installation mark the provision of a cowl. Ask the assistant to take a cowl (1). A small screw-driver raise a lock spring (arrow) a little. Disconnect a gas-filled emphasis (5) from the top spherical support. Turn on on two nuts (4) it is left and on the right and remove a cowl together with the assistant.

Installation

 PERFORMANCE ORDER

    Establish a cowl together with the assistant on a loop (2). Adjust the provision of a cowl on earlier put label. Establish and fix a gas-filled emphasis on a spherical support. Close a cowl and expose it, observing gaps, see below. Tighten nuts (4) moment 21Нм. Installation is carried out in sequence, return to removal. Attach a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

Check/adjustment

 PERFORMANCE ORDER

    Check gaps on a cowl contour. Gaps should be uniform on all perimeter of a prileganiye to body elements.

    And — 5.5 ± 0.5 mm
    In — 5.5 ± 0.5 mm
    With — 3.5 ± 0.5 mm
    D — 4.0 ± 0.5 mm
    Е — 1.5 ± 0.5 mm
    F — 1.5 ± 0.5 mm
    G — 2.5 ± 0.5 mm

    Weaken a nut (4) a little, address to an illustration at the beginning of the section.
    Close a cowl and expose it on wings. Adjust the provision of a cowl. Carefully open the exposed cowl not to shift it. Tighten nuts of fastening of loops the moment 21Нм.
    Weaken 4 bolts of fastening so that it was possible to displace the lock (1).
    Adjust a cowl by lock shift on height. Tighten bolts of fastening of the lock the moment 14Нм.
    Adjust the provision of a cowl on height in relation to wings. For this purpose screw a forward emphasis (1) and (2) at a cowl. By a reversing of an emphasis adjust cowl height in relation to wings. Put a little plasticine between a cowl and wings and check, whether has an emphasis at the closed cowl contact to the forward panel. An emphasis at the closed cowl should adjoin to the forward panel.

Utilization of a gas-filled emphasis

 PERFORMANCE ORDER

If the gas-filled emphasis is replaced, it is necessary to let out gas from an old emphasis.

    For this purpose clamp an emphasis in a vice in the area designated on an accompanying illustration (x = 50 mm).

Emphasis clamp surely only and the specified area, otherwise there is a danger of accident! Then надпилите the cylinder at distance of one third of total length from a base mark from a rod. For protection against emission of oil cover the area реза with a rag. Besides, in time a pileniye use goggles.