Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures at carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and window regulator installation
      Removal and installation of the electric motor of a drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and trunk lid adjustment
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + salon Equipment
+ Onboard electric equipment


f6be02a9 roslmk.ru

Removal and installation of the lever of a cleaner of back glass

Versatile person

Removal

 PERFORMANCE ORDER

    Stop a screen wiper in extreme situation.
    Mark the provision of a brush on glass, for example, by means of a sticky tape.
    Carefully hook and uncover (4) a cleaner axis up.
    Carefully remove a jet (3) from a connecting tube.
    Weaken a nut (2) and remove the lever (5) from an axis. (6) – brush.

Installation

 PERFORMANCE ORDER

    Check, that the electric motor of a screen wiper stood in extreme situation. If necessary, quickly start the electric motor and stop it the switch. Establish the lever on an axis of a screen wiper and will expose it by means of a label put at removal. It is possible to expose also the lever on distance between a brush and the bottom edge of glass, having measured it from the right top of a cleaner. Adjusting size: from 15 to 20 mm. Screw a nut and tighten it by hand. Check extreme position of the lever, if necessary, again adjust. Tighten a nut the moment 12Нм and close it a cover.