Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures at carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and window regulator installation
      Removal and installation of the electric motor of a drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and trunk lid adjustment
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + salon Equipment
+ Onboard electric equipment


f6be02a9

Removal and installation of moldings

Door molding

Moldings are pasted to a body and at their removal collapse.

Removal

 PERFORMANCE ORDER

    Heat up parts moldings (1) and (2) hair dryer and separate them from a door.

Installation

 PERFORMANCE ORDER

    Clear a place where the level will be pasted, gasoline, process a silicone udalitel and dry.

Moldings should be pasted only at room temperature. For this purpose the car and levels at least in two hours prior to gluing should be placed indoors with room temperature.

    Remove a protective film (3) with a bilateral sticky tape (4). Insert a molding pins into openings on a door and paste. Heat up a molding the hair dryer to temperature of 40 °C and strongly press or roll.

After a prikleyka of moldings hold the car within four hours at room temperature.

Molding of the bottom beam

Removal

 PERFORMANCE ORDER

    Turn out screws (3) and put forward a forward molding (1) back from holders.

Similarly remove a back molding (2).

Installation

 PERFORMANCE ORDER

    Establish a molding on the bottom beam, move forward in holders and fix screws.