Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Rassoyedineniye of sockets
   Check of the electric motor of a screen wiper
   Check of warmed back glass
   Check of stoplights
   Removal and installation of a sound signal
   Removal and installation of sensors of a parking
   Replacement of the battery of a remote control of the ignition key
   Relay and safety locks
   Replacement of filament lamps of devices of external lighting
   Removal and installation of headlights
   Removal and installation of the lateral repeater of turns
   Removal and installation of an additional stoplight
   Removal and installation of a back lamp
   Removal and installation of a lamp of illumination of registration plate
   Removal and installation of plafonds of internal lighting
   Removal and installation of a control panel
   Removal and installation of the podrulevy switch
   Removal and installation of switches of a forward door
   Removal and installation of the switch of light
   Removal and installation of the switch of a window regulator in a back door
   Removal and installation of the switch of a trunk lid
   Removal and installation of the switch of the parking brake
   Removal and installation of the switch of illumination of a ware box
   Removal and installation of switches of the central console
   Removal and radio receiver installation / navigation device/CD-чейнджера
   Removal and installation of loudspeakers
   Removal and installation of aerials
   Removal and installation of the tank of liquid стеклоомывателя / pump electric motor
   Removal and installation of the electric motor of a cleaner of a windscreen
   Removal and electric motor installation on back glass (Versatile person)
   The uniform lock - the general information
   Removal and installation of a locking element of a cover of a fuel tank
   Digital tire of data of CAN
   + Schematic diagrams of electric equipment


f6be02a9

Replacement of filament lamps of devices of external lighting

Devices of system of lighting treat: headlights, fog lights, back lamps, stoplights, backing lamps, indexes of turns, foggy lamps, lamps of illumination of registration plate and devices of internal lighting.

The exit of the filament lamp is out of operation displayed on the universal display. (Information system of the driver (FIS)).

There is a danger of a travmirovaniye!

Be careful at replacement of xenon lamps of a high voltage in headlights! Just in case switch off a headlight and disconnect the storage battery. After replacement quickly switch on and off a headlight to remove residual stress. For reasons of safety carry footwear with rubber soles.

Filament lamps and holders of lamps can appear very hot. Therefore before replacement of filament lamps wait coolings of the lighting device.

Store lamps in a place inaccessible to children.

Do not apply the fallen lamps or lamps with scratches, they can burst.

The glass flask of the filament lamp should not be taken hands. It is for this purpose best of all to use napkins or cotton gloves. Fingerprints evaporate and besieged on a reflector, obscuring it. On a flask it is necessary to remove casually formed spots by means of pure, not containing fibers, a towel moistened in alcohol.

It is necessary to replace filament lamps only with lamps of the same execution.

 PERFORMANCE ORDER

    Switch off ignition and the headlight switch. Disconnect a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

Passing beam

 PERFORMANCE ORDER

    Right headlight: Disconnect the top cover of the engine, and also an air line between the forward panel and the air filter. Left headlight: Remove a headlight, address to appropriate section. Uncover a reverse side of a headlight. For this purpose take away a wire bracket from a cover.
    Galogenovy lamp: Disunite the socket (2), take away a wire bracket and remove a lamp (3).
    Xenon lamp: Turn the tip (1) counter-clockwise and remove. Release wire brackets (arrows on an accompanying illustration) and take out a lamp from the case.
    Insert into the case a new lamp, fix it a bracket and join the socket. Establish a cover from a reverse side of a headlight and fix a bracket. Further installation is carried out in sequence, return to removal.

Driving/parking light

 PERFORMANCE ORDER

    Right headlight: Disconnect the top cover of the engine, and also an air line (subsection "Passing beam"). Left headlight: Disunite sockets over a headlight, unblock the holder and remove it upward. Uncover a driving beam a reverse side of a headlight. For this purpose take away a wire bracket from a cover.
    Galogenovy headlight: Turn the electric motor of adjustment of range of light, remove from a headlight and put aside.

At the right headlight turn counter-clockwise (an arrow on an accompanying illustration), at the left headlight clockwise.

    Lay light / xenon headlight: Turn the electric motor of adjustment of range of light, remove from a headlight and put aside.
    Driving beam: Disunite the socket (3), release a bracket (2) and take out a lamp (1) of the case. Insert a new lamp, fix it a bracket and join the socket.
    Parking light: Release lock pads and take out a cartridge (the shooter on an accompanying illustration) from the case. Take out a lamp from the boss, replace it on new and insert a cartridge into the case.
    Establish from a reverse side of a headlight the electric motor of adjustment of range of light, establish into place a cover of a headlight and fix it a bracket. Further installation is carried out in sequence, return to removal.

Turn index

 PERFORMANCE ORDER

    Remove a headlight, address to the Section Removal and installation of headlights.
    Turn a cartridge (the shooter on an accompanying illustration) counter-clockwise and take out it from the case.
    Press a lamp into a cartridge, turn and take out. Replace a lamp new and insert a cartridge into the case. Establish into place a headlight, address to the Section Removal and installation of headlights.