Audi A4, S4

since 2000 of release

Repair and car operation

Lighting and providing review

External lighting and light alarm system

Inclusion and light switching off

Inclusion of lay fires

Inclusion of a passing or driving beam

Light switching off

The passing beam burns only at the included ignition. During start of the engine and after switching off of ignition there is an automatic switching on lay fires.

In some export updatings in addition to lay fires the passing beam of the lowered brightness burns.

When using the above described signaling and lighting devices observe standard requirements.

Automatic light of headlights (operated by a sensor)

Depending on external illumination in position of the Auto switch it joins/is turned off the light headlights.

Light switch — Regulator of a tilt angle of light of headlights — Switch of illumination of the road to the house/car

The passing beam operated by a sensor on the properties corresponds to light of headlights without function of a driving beam.

Inclusion of light of headlights

Switching off of light of headlights

In the situation AUTO in the switch of light the corresponding symbol burns.

In case of automatic inclusion of light of headlights the passing beam, a parking light, back lamps and illumination of registration plate lights up.

The switch of light it is possible in a manual mode and further to include lay fires, light of headlights, fog lights and back foggy lamps.

Established in the case of an internal rear-view mirror sensors of illumination supervise external illumination. In case of decrease in external illumination (for example, at movement in a tunnel) is lower than the manufacturer of value established at plant automatically it is turned on the light headlights. At the subsequent increase in external illumination the passing beam is automatically switched off.

Do not place on a windscreen before a sticker sensor to exclude violation/refusal of function of automatic light of headlights and automatic blackout of a mirror.

Fog lights

The switch of light also fog lights join.

Inclusion of fog lights

At the included fog lights near the switch the symbol lights up .

Models with back foggy lamps

Back foggy lamps

The switch of light also back foggy lamps join.

PERFORMANCE ORDER

Turn light switch without calling on a symbol Turn in the beginning light switch in situation or . Then extend light switch before the second fixed situation (2). Back foggy lamps join.

At the included back foggy lamps near the switch symbols are shone and .

The system of electric equipment of cars with the traction coupling device of a factory complete set provides automatic shutdown of back foggy lamps of the car at trailer operation.

In order to avoid dazzle moving behind drivers include back foggy lamps only in the conditions of a fog.

Function of illumination of the road to the house / to the car

In the dark by means of this function the space round the car is automatically shined.

Function inclusion

Function switching off

the button is in situation 1; it is turned off the light headlights and ignition; dark conditions of lighting, sensors do not identify or identify only insignificant brightness.

Function of illumination of the road to the house (Coming-home)

At the included system and in the dark, right after opening of a door of the driver, lay fires, back marker lights and illumination of registration plate join.

If it is open any a door/luggage carrier, fog lights remain included approximately within 4 minutes.

For illumination of the road fog lights remain included still approximately within 30 seconds after closing of doors and a luggage carrier.

You can change the duration of inclusion established at manufacturer if necessary. The maximum duration of inclusion can make 60 seconds.

Function of illumination of the road to the car (Leaving-home)

When unlocking car by the button of a radio key fog lights join.

Fog lights are switched off when opening a door of the driver. If the door of the driver does not open, fog lights are switched off at the subsequent automatic locking of the car, see. Unlocking and car locking. *

You can leave function of illumination of the road to the house / to the car constantly included. However management of system is carried out through light sensors and consequently it works only in dark conditions of lighting.

Especially at movement on short distances during dark time, with constantly included this function, load of the storage battery increases. For the purpose of a sufficient battery charging trips on distant distances, from time to time, are necessary.

At the included function of illumination of the road to the house / to the car, after inclusion of ignition burning fog lights are switched off.

Illumination of devices

Brightness of devices, displays and illumination of the central console is regulated only at included light.

Illumination of devices

PERFORMANCE ORDER

For increase in brightness press the button «+». For reduction of brightness press the button «-».

At the included ignition

At inclusion of ignition it is possible to regulate brightness of a background of indexes (arrows) of a control panel.

At included light

Besides, at included light, pressing of buttons «+» and «-» it is possible to regulate brightness of devices, displays and illumination of the central console.

Regulation of a tilt angle of headlights

At the included passing beam it is possible to bring into accord ranges of light of headlights with the actual loading of the car.

PERFORMANCE ORDER

Deblock the button it in pressing. For regulation of a light cone turn the button in demanded situation. In summary, in order to avoid imprudent shift of a light cone, wring out the button in a starting position.

Provision of a regulator

Noted provisions of a regulator approximately correspond to the following options of loading of the car:

(0) — in the car the driver and the forward passenger, a luggage carrier is empty

(2) — all places are occupied, the luggage carrier is loaded

(3) — the place of the driver is taken, the luggage carrier is loaded

In order to avoid dazzle of drivers of counter transport, surely regulate a tilt angle of headlights according to car loading!

Dynamic regulation of a tilt angle of headlights

At inclusion of ignition and during car movement to xenon light there is an automatic control of a tilt angle of headlights according to loading and a movement mode (for example, at dispersal, braking).

About malfunction the alarm symbol in the monitoring system of malfunctions of the car * signals, see. Information system of the driver (FIS).

Alarm light system

The alarm light system should in dangerous situations pay attention of other participants of traffic on your car.

For inclusion or switching off of the alarm light system press the switch.

At the switched-on alarm light system all lamps of indexes of turn at the same time blink. The control lamp in the switch Besides, blinks, and also shooters of indexes of turn in a control panel blink. The alarm system works and at the switched-off ignition.

At failure with disclosure of safety cushions the alarm light system turns on automatically.

Lever switch of indexes of turn and switch of a driving beam

The lever switch of indexes of turn and the switch of a driving beam also lay fires and a light signal join.

Lever switch of indexes of turn and switch of a driving beam

Functions of the lever switch of indexes of turn and switch of a driving beam:

Turn indexes

Driving beam

Light signal

Lay fire

PERFORMANCE ORDER

Switch off ignition. For inclusion of the right lay fires take away the lever up, and for inclusion of the left lay fires take away the lever down.

Indexes of turn work only at the included ignition. At the included indexes of turn in a control panel also corresponding control lamp or blinks, see. Governing bodies and devices.

After an exit from turn indexes are switched off automatically.

The driving beam can be included only at the included passing beam. Thus in a control panel the control lamp lights up.

The light signal burns at procrastination and lever keeping, and also at switched-off light. Thus in a control panel the control lamp of a driving beam lights up.

At included lay fires headlights and back lamps of the lowered brightness of the relevant party of the car burn. Lay fires burn only at the switched-off ignition.

Include a driving beam or a light signal only provided that as a result there will be no dazzle of other participants of traffic.

Illumination of salon

Forward plafonds and lamp of illumination of a ware box

Illumination of a forward part of salon includes also lamps of individual illumination of the driver and the forward passenger.

Positions of the keyboard switch (A) of a forward plafond:

Operation from door switches

PERFORMANCE ORDER

Establish the switch (A) in average situation.

Plafond inclusion

Plafond switching off

Forward lamps of individual lighting

Illumination of a ware box

Illumination of the ware box located from the forward passenger automatically joins when opening a box and the included headlights or lay fires. When closing box lighting is switched off.

If the plafond is in the provision of operation from door switches, it joins when unlocking the car or opening doors. Besides, the plafond joins at key extraction from the ignition lock. Light dies away approximately in 30 seconds after closing of doors. At inclusion of ignition or when locking car the plafond is switched off.

In order to avoid an accumulator discharge illumination of salon is automatically switched off, if the door remains open more than 10 minutes.

Brightness of light of lamps at inclusion and switching off is automatically regulated by a svetoregulyator.

Accompanying lighting

Accompanying lighting highlights important governing bodies.

At ignition inclusion lighting in door handles automatically joins.

At inclusion of lay fires or light of headlights lighting over a windscreen joins also. On the central console light falls from above.

Accompanying lighting cannot be switched off manually.

Back lamps of individual lighting

Lamps of individual lighting join and switched off by keys .

Illumination of a luggage carrier

The lamp is located in the top part of a trunk lid. One more lamp is established from the interior of a back wall.

Lighting joins automatically when opening trunk lid. Lighting is automatically switched off, if the luggage carrier remains open more than 10 minutes.

Visibility

Windscreen heating

Heating of a windscreen releases glass from moisture.

For inclusion or switching off of heating of a windscreen press the button .

Heating of a windscreen is possible only at the working engine. At the included heating in its switch the control lamp burns. In an automatic mode of the AUTO conditioner of the car with the cold engine and at external temperature less +5°С, heating of a windscreen joins automatically. Duration of heating depends on external temperature and makes at most 6 minutes. Thus the conditioner should work in a heatproductivity mode. In the set mode , and at external temperature less +5°С, function of automatic heating of glasses in addition joins. Duration of heating depends on external temperature and makes at most 6 minutes.

In the set ECON mode heating of a windscreen is disconnected.

Windscreen heating automatically is disconnected in case of education on a crack windscreen as a result of influence of extraneous subjects (for example, blow by a stone). The conditioner is disconnected to prevent further increase in a crack. Replace glass.

Heating of back glass

Heating of back glass releases back glass from moisture.

For inclusion or switching off of heating of back glass press the button .

Heating works only at the included ignition. While it is included, in its switch the control lamp burns.

At external temperature more 0°С heating of back glass is switched off approximately in 10 minutes independently.

At the included heating of back glass depending on external temperature обогревается* a surface of mirrors.

Sun-protection peaks

Sun-protection peaks promote traffic safety increase.

Sun-protection peak

Sun-protection peaks (1) driver and the forward passenger can be released from clamps and be taken away with turn to doors.

Sun-protection peaks are completed with a cosmetic mirror with a cover. Illumination зеркал* (a lamp in a ceiling) joins automatically when moving a cover (2) and is switched off at its return to a starting position. Besides, lighting is switched off and when closing a sun-protection peak.

Sun-protection curtain

Windows of back doors and back glass are respectively completed with a sun-protection curtain.

Sun-protection curtain (back doors)

PERFORMANCE ORDER

Extend a curtain and fix it for hooks of top of a doorframe.

Sun-protection curtain (back glass)

PERFORMANCE ORDER

For lowering or a podnimaniye of an electrodriving sun-protection curtain of back glass press a key of an electrodriving curtain of back glass.

Having reached extreme top or bottom situation, the curtain is automatically switched off. During curtain movement up or down in pressing of a key it is possible to change its direction of movement. At ignition switching off during lifting or curtain lowering, it will stop not at once, but only after achievement of extreme situation.

At repeated, without appropriate pauses, inclusion of a curtain the protection provided in its drive against an overload works. In this case the subsequent inclusion is possible only after some time.

As on a frost the material of a curtain loses elasticity, at temperature in salon - 5°С its drive is disconnected. In this case the switch of a curtain can use only after excess of this threshold value.

Screen wiper

The handle of a screen wiper the screen wiper, and also an automatic mode of a screen wiper and a stekloomyvatel joins.

Short-term mode

Interval mode

PERFORMANCE ORDER

Take away the handle up in the fixed situation (2). Regulator (A) duration of intervals of inclusion of a screen wiper changes.

Slow mode

The accelerated mode

Screen wiper and stekloomyvatel collaboration in an automatic mode

Switching off

The system of screen wipers and stekloomyvatel works only at the included ignition.

In some seconds after switching off of a screen wiper of a brush automatically work once again.

Duration of intervals depends also on speed of the car.

Jets of a stekloomyvatel are warmed at the included ignition.

For windscreen cleaning at included light it is necessary to pull the screen wiper handle quickly only. Otherwise at longer procrastination of the handle the faroomyvatel * will join also that will lead to useless use of washing liquid in the refueling tank of a stekloomyvatel.

In a frost before the first inclusion of a screen wiper check, whether brushes froze! Otherwise it is possible to damage not only brushes, but also the screen wiper electric motor!

Before long trips track, that the tank of a stekloomyvatel was filled, see. Head Current leaving and service.

Faroomyvateli

At included light pull the handle in situation (5) (screen wiper and stekloomyvatel collaboration in an automatic mode) and hold the handle in this situation more than 1 second.

At work jets of washers of headlights under the pressure of water are put forward outside.

Regularly, for example when filling, delete from glasses of headlights dirt not giving in to washing off (traces from insects).

For preservation of operability of system in winter conditions clear nests of washing jets of snow, and also delete from there ice, using for this purpose an aerosol razmorazhivatel.

Replacement of brushes of a screen wiper

Reliable work of brushes of a screen wiper is obligatory for good visibility.

Brush removal

PERFORMANCE ORDER

Take away the screen wiper lever from glass. Press the button (A). Remove a brush.

Installation of a brush of the driver

PERFORMANCE ORDER

Expose a screen wiper brush in holders (A) and (B). For brush fixing on the lever press the button (C). In summary check correctness of fastening of a brush.

Installation of a brush of the forward passenger

Rear-view mirrors

Internal mirror with manual blackout

Normal situation

Provision of blackout

Internal mirror with automatic blackout

Function of automatic blackout can be disconnected and included if necessary.

Blacked-out internal mirror: control lamp and inclusion/switching off key

Switching off of function of blackout

Inclusion of function of blackout

PERFORMANCE ORDER

Press a key (A). The control lamp (B) burns.

Blackout function

Function of automatic blackout joins each time at ignition inclusion. In the case of a mirror the green control lamp burns.

At the included function of blackout there is an automatic blackout of light of an internal mirror depending on a stream of light falling on it. Also at the included function blackout of a mirror does not occur in the following cases:

at inclusion of internal lighting; at inclusion of transfer of a backing.

Sensors of automatic light фар*

When finding the switch of light in the situation AUTO by means of established in the case of a mirror of sensors depending on external illumination the passing beam automatically joins and switched off.

In case of switching off of function of blackout of an internal rear-view mirror function of automatic blackout of external mirrors is disconnected also.

Trouble-free function of automatic blackout of mirrors is possible only at the cleaned sun-protection curtain back стекла* and when with a stream of light falling on an internal mirror interferes nothing.

Do not place on a windscreen before a sticker sensor to exclude violation/refusal of function of automatic light of headlights and automatic blackout of a mirror.

External mirrors

The provision of external mirrors is regulated by the electric drive.

Installation of external mirrors

PERFORMANCE ORDER

Rotation of the multiitem switch (button) carries out switching on the left external mirror (situation (L)) or the right external mirror (situation (R)) In button pressing in the directions specified by shooters so adjust a reflective surface of external mirrors that the sufficient back review was provided.

Folding both зеркал*

Складывать* external mirrors it is recommended, for example, for their preservation at a parking or in narrow spaces.

Heating зеркал*

The reflective surface of external mirrors is warmed at the included ignition depending on external temperature.

Automatic equipment of a deviation of a mirror of the forward passenger in the cloth direction дороги*

When switching electric drive on a mirror of the party of the forward passenger (situation (R)) and inclusion of transfer of a backing the reflective surface of a mirror slightly deviates down. Thereby visibility of a bordyurny stone is provided at a parking.

The mirror comes back to a starting position after switching off of transfer of a backing and car movement forward with a speed more than 15 km/h or when switching electric drive on a mirror of the driver (L) or switching in neutral situation (D).

Memory of situation external зеркал*

When programming provision of a seat of the driver of cars with a memory of provision of a seat of the driver the standard position of external mirrors is automatically programmed also, see. Seats and niches.

Convex and сферические* mirrors increase review sector. However they reduce the image of objects. Therefore such mirrors are only conditionally suitable for a distance assessment to moving behind vehicles.

At mirror shift as a result of influence of external forces (for example, blow when maneuvering) carry out complete electric folding of mirrors. At all do not establish a mirror in a starting position a hand as it can negatively affect their work.

Automatically blacked out external mirrors

External mirrors are blacked out automatically together with an internal mirror. At the included ignition there is an automatic blackout of light of mirrors depending on a stream of light falling on them (for example, light of headlights behind).

At inclusion of illumination of salon or transfer of a backing of a mirror come back to a starting position (without blackout).

Trouble-free function of automatic blackout of a mirror is possible only at the cleaned sun-protection curtain back стекла* and when with a stream of light falling on an internal mirror interferes nothing.