Audi A4, S4

since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
- Suspension bracket and steering
   Security measures at work
   + Suspension bracket of forward wheels
   + Suspension bracket of back wheels
   + Corners of installation of wheels of the car
   - Steering and safety cushions
      General information and security measures
      Removal and installation of the block of a safety cushion
      Removal and installation of a steering wheel
      Removal and installation of a tip of steering draft
      Removal and installation of a protective cover of the steering mechanism
+ Body
+ Onboard electric equipment


f6be02a9

Removal and installation of the block of a safety cushion

Driver's safety cushion

1 — Torx T30, 7Нм Screws
2 — the Steering wheel, various executions
3 — the spring Tip
4 — the Tip of the block of a safety cushion
5 — the safety cushion Block

6 — the Tip of a sound signal
7 — the Screw with an internal polyhedron, 50Нм
8 — the Tip of heating of a steering wheel
9 — the Returnable ring with a contact ring

Removal of a driver's safety cushion

1 — the Steering wheel
2 — the Socket of a spiral spring
3 — the Socket of the module of a safety cushion
4 — the Multicontact bolt
5 — the Carving plug
6 — the Module of a safety cushion of the driver

7 — Torx T30 Bolt
8 — Torx T30 Bolt
9 — the Spiral spring
10 — Torx Key
11 — the Socket of heating of a steering wheel

Arrangement of elements of systems of safety in salon

1 — the Module of management of a safety cushion
2 — the Module of a safety cushion of the forward passenger
3 — the Sensor of presence of the forward passenger
4 — the safety cushion Module on the right
5 — Management of the right seat

6 — the Module of a safety cushion of the left seat
7 — the safety cushion Module at the left
8 — the Diagnostic socket
9 — the Spiral spring
10 — the Module of a safety cushion of the driver

The failure sensor for safety systems

Fastening of a safety cushion of the forward passenger

1 — the Safety cushion of the forward passenger
2 — the Basic arm
3 — the Assembly bracket
4 — the Angular bracket
5 — the Assembly bracket

Block of a head safety cushion

1 — the Rack of D
2 — the Fuse
3 — the Bolt
4 — the Holding loop
5 — the Head lateral safety cushion
6 — the handle Adapter
7 — the Latch
8 — the Rack And

9 — Samokontryashchiyesya bolts
10 — the Rack In
11 — the Rack With
12 — the Latch
13 — the Bolt
14 — I Will corrode electroconductings
15 — to Bend back and to fix

Removal of the block of a lateral safety cushion

Removal of the control unit of systems of safety

Removal

 PERFORMANCE ORDER

    Read and follow instructions on security measures at the address with a safety cushion. Disconnect a negative cable (-) the storage battery.

Observe indications of the Section Replacement of the storage battery.

    Isolate plugs of the storage battery. Unblock the mechanism of adjustment of provision of a steering column. Will put forward a steering wheel (2) as far as it probably and pull it up. Establish vertically, address to an illustration the Driver's safety cushion. Unscrew one of two Torx T30 screws (1). Turn a steering wheel on a half of turn back and unscrew the second Torx (1) screw. Disunite the socket of the block of a safety cushion (4). Disunite the socket of a sound signal (6). Put the block of a safety cushion (5) so that the shock party of a pillow showed up.

Installation

 PERFORMANCE ORDER

    Join sockets (4) and (6) and fix them lock brackets (distinct click should be heard). Watch that any cable did not adjoin to the generator of gas and that the cable was not pressed. Combine a safety cushion cable at the left in the form of a loop. Combine in a loop a cable of a sound signal. Tighten screws (1) moment 7Нм, address to an illustration the Driver's safety cushion. Include ignition. Attach a negative cable of the storage battery.

At connection of the storage battery in salon of the car there should not be people.