Audi A4, S4

since 2000 of release

Repair and car operation

Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
- Suspension bracket and steering
   Security measures at work
   + Suspension bracket of forward wheels
   - Suspension bracket of back wheels
      General information
      Removal and installation of a screw spring
      Removal and shock-absorber installation
   + Corners of installation of wheels of the car
   + Steering and safety cushions
+ Body
+ Onboard electric equipment

Suspension bracket of back wheels

General information

Suspension bracket of back wheels


1 — the Shock-absorber 2 — a suspension bracket Beam 3 — the Screw spring 4 — the Brake disk	5 — the wheel Bearing 6 — the Mechanism of adjustment of convergence 7 — the Mechanism of adjustment of disorder

Suspension bracket levers. Models with a forward drive

1 — Trapetsiidalny the lever. At damage of support the lever replace
2 — Ekstsentrikovy the screw, provides convergence adjustment. Turns away to the left and to the right on a corner no more than 90 °
3 — Ekstsentrikovaya a washer
4 — the Nut *, 95Нм
5 — Combined винт*
6 — a spring Support bottom
7 — the Screw spring
8 — a spring Support top
9 — a spring Support top, only for the running gear intended for bad roads
10 — the Combined screw *, 85Нм + 90 °
11 — the Cross-section lever
12 — Ekstsentrikovy the screw. Provides disorder adjustment, turns away to the left and to the right on a corner no more than 90 °

13 — the Washer
14 — the Nut *, 85Нм + 90 °. Being self-stopped, at a tightening of bolts the car should stand wheels on the earth.
15 — Cross-section draft
16 — the Guard for protection against hit of stones, only for the running gear intended for bad roads
17 — the Nut with a fillet *, 85Нм + 90 °. At an inhaling the car should stand wheels on the earth
18 — the Guard for protection against hit of stones, only for the running gear intended for bad roads
19 — the Bolt with a fillet, 25Нм
20 — the Holder of a cable of a drive of the parking brake
* surely replace

Shock-absorber, fist and wheel nave

1 — the Fist, models with a forward drive
2 — the Nave with the wheel bearing. Repeatedly apply only in a case when the block acts in film manually. Otherwise it is necessary to replace it in a set. The bearing and a nave are located in one case. The bearing a wheel/nave do not demand service. Adjustment or repair are not made
3 — the Bolt with a fillet
4 — the Boot
5 — the Sensor of number of turns of a wheel

6 — the Screw with an internal shestigrannik, 10Нм
7 — the Nut, 150Нм + 90 °. Replace. At an inhaling the car should stand on wheels
8 — the Washer
9 — the Shock-absorber
10 — the Combined bolt, 36Нм
11 — the Combined bolt

The suspension bracket of back wheels is equipped with trapetsiidalny levers. The beam of a suspension bracket is executed from steel, trapetsiidalny levers - from a hollow aluminum profile. Such design is characterized by insignificant weight and compactness. Thanks to it becomes possible to reach both at front-wheel option, and at a full drive of a low arrangement of a floor in a luggage carrier and optimum width of a cargo compartment.

All lever elements through rezino-metal support are connected by hinges to elastically established beam of a suspension bracket that provides effective clearing of vibrations of a body. Podressorivaniye of a back suspension bracket is carried out by screw springs and two shock-absorbers which are located separately and easily act in film.

Carrying out welding and leveling works on bearing and directing elements of a forward suspension bracket is not allowed. Being self-stopped nuts, and also rusty bolts/nuts, at carrying out repair should be replaced.