Audi A4, S4

since 2000 of release

Repair and car operation

Audi A4, S4
+ Introduction
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
- Suspension bracket and steering
   Security measures at work
   - Suspension bracket of forward wheels
      General information
      Removal and installation of an amortization rack
      Removal and installation shock-absorber/dismantling of an amortization rack
   + Suspension bracket of back wheels
   + Corners of installation of wheels of the car
   + Steering and safety cushions
+ Body
+ Onboard electric equipment

Removal and installation shock-absorber/dismantling of an amortization rack

Elements of an amortization rack


1 — the Nut with a fillet, 50Нм, being self-stopped, surely replace 2 — a shock-absorber Support 3 — the Washer 4 — the Support 5 — the Screw spring	6 — the Additional spring 7 — the Protective casing 8 — the Protective cap 9 — a spring Support bottom 10 — the Plate of a spring bottom 11 — the Shock-absorber

Removal

PERFORMANCE ORDER

Remove an amortization rack. The amortization rack can deal only with use of the special tool.

The spring of an amortization rack is compressed by big effort. For removal of the shock-absorber it is necessary to compress a spring the special adaptation.

At all do not remove the shock-absorber if the spring reliably is not compressed. At adaptation installation for compression of a spring watch that rounds of a spring were reliably captured and the adaptation could not slide off. The spring is compressed by big effort. Apply only the reliable tool. At all do not connect a spring a wire. Danger of accident!

Clamp a spring with a tip in a vice.

Compress a spring the corresponding adaptation. HUNDRED AUDIS apply the V.A.G 1752/1 (1) adaptation to this purpose.

At compression watch the correct provision of a spring in the adaptation (an arrow on an accompanying illustration). (1) – the adaptation for compression, (2) – a support for spring rounds.

Compress a spring so that the top plate was released. Unscrew a nut with a fillet of fastening of a rod. Thus hold a rod from a provorachivaniye a face key for an internal shestigrannik. The special tool (2, 3 and 4), shown on an illustration 4.3 (is for this purpose necessary for HAZET 4910/13 or AUDI-T10001/7, T10001/11 and T10001/3). Remove the compressed spring together with the adaptation for compression.

Remove a protective casing (1) and the bottom support of a spring (2).

Mark the provision of the bottom plate in relation to the shock-absorber (4). Disconnect a plate (3) by means of a plastic hammer and remove upward.

Installation

There are springs of various groups of the admission. It is necessary to apply only springs with an identical color label. It is recommended to replace springs and shock-absorbers in pair, i.e. from both parties of the car.

PERFORMANCE ORDER

And — a shock-absorber Axis / the bearing lever
I\Left amortization rack,
In = 65 ± 2 °
II\Right amortization rack,
With = 87 ± 2 °

The provision of the bottom plate is defined by the sizes specified an illustrations. The cut of a plate (shooter) should provide access to a body.

Establish into place the bottom support of a spring and a protective casing.

Establish into place compressed spring together with the adaptation for compression. The end of a round of a spring should adjoin to an emphasis.

Establish a shock-absorber support with the top support of a spring on the compressed spring so that the support of a spring adjoined by the end of a round of a spring (the shooter on an accompanying illustration). The deviation within ± 2 ° is allowed.

Establish a washer and a shock-absorber support.

Watch that the end of a spring adjoined to an emphasis of the top support of a spring.

50Нм.

Release the bottom lock lever and turn the top plate of a spring so that the scale of a support of an amortization rack stood on a mark 7 °.

I\At the left in the movement direction
II\On the right in the movement direction
And — a shock-absorber Axis / the bearing lever
B — an installation Corner

Fix the lock lever. The lever of a support of a spring of the V.A.G 1752/2 adaptation (shooter) should coincide with the support center. Carefully weaken the adaptation for compression of a spring and take out it. Check adjustment. If necessary, repeat procedure. Establish into place an amortization rack, address to appropriate section.