Audi A4, S4

since 2000 of release

Repair and car operation

Automobile himikaliya, oils and greasings

Cleaners

The cleaner for brake systems is applied to removal of traces of greasing and brake liquid from surfaces a component of brake system where absolute purity is a paramount condition of efficiency of functioning. The cleaner does not leave any traces and in many cases eliminates the squeal of brake mechanisms caused by pollution their component.

The cleaner for electric a component promotes elimination of oxide films, corrosion and deposit traces from contact surfaces without elektroprovodnost violation. Also it can be used for cleaning of spark plugs, jets, regulators of tension and other knots where complete cleaning of oil and fat is desirable.

To Vlagopoglotiteli serve for water and moisture removal from surfaces such electric a component as the generator, a tension regulator, a box of safety locks, electric sockets, etc. Vlagopoglotiteli usually are not current-carrying, not causing corrosion and not inflammable.

Obezzhirivateli is represented by superstrong solvents and serve for removal of traces of greasing from external surfaces of the engine and a chassis component. Are issued in the form of aerosols or are put with a brush or a brush and, depending on type, are washed away either water, or solvent.

Greasing liquids

Qualities of impellent oils

– all-the-year-round use in zones of a temperate climate;

– excellent washing properties;

– good greasing ability at all temperatures and engine loadings;

– high stability of initial properties for a long time.

All-weather oils with the improved antifrictional qualities have, besides, additional advantages:

– all-the-year-round use honor at all possible temperatures of external air;

– small losses of engine capacity on a friction;

– simplification of cold start of the engine – even at very low temperatures.

Seasonal oils owing to specific vyazkostno-temperature properties inherent in them usually cannot be used all the year round. Therefore these oils should be applied only in extreme climatic zones.

When using all-weather oils of the class SAE 5W-30, it is necessary to avoid long operation of the engine with high frequency of rotation and constant big load of the engine. These restrictions are not valid for all-weather oils with the improved antifrictional qualities.

Additives to impellent oils

Adhere to a rule: always to use high-quality oil of one brand corresponding to the engine (on classification) and not to risk to mix it with same synthetic (or semi-synthetic) oil. The engine will thank for it reliable work. Do not buy oil privately as packing is easy for forging.

Transmission oil is developed for application in differentials, transmissions, and other knots where stability to influence of high temperatures is required.

Greasing for a component of the chassis and bearings of wheels represents the dense greasing applied in knots, subject to the raised loadings and a friction, such as bearings of wheels, spherical support of a suspension bracket, tips of steering drafts and kardanny hinges.

High-temperature greasing for bearings of wheels is capable to resist to influence of the high temperatures arising in bearings of wheels of cars, equipped with disk brake mechanisms. Usually contains the disulfide of molybdenum being greasing substance of dry type.

White greasing (tsiaty) represents the dense greasing put on metal surfaces contacting among themselves in places where there are problems with the increased moistening. Remains soft both at low, and at high temperatures, it is not washed away and it is not diluted by water.

Assembly greasing represents special greasing, for application in the conditions of high pressures, usually contains molybdenum and is used for greasing of the knots subject to raised loadings (such as radical and shatunny bearings and working ledges of cams) before the first start of the engine after completion of major maintenance.

Silicone greasings are applied to protection rubber, plastic, vinyl and nylon a component.

Graphite greasings serve for application where oil cannot be used in a type of problems with pollution (for example, in locks). Dry graphite perfectly greases metal details, preventing influence on them of moisture, acids and other aggressive pollution. Greasing is electrowire and does not break contact in such knots, as, for example, the ignition lock.

Getting structures are applied by Molibdensoderzhashchiye to simplification of an otdavaniye of the "become attached" fixture, and also for fixture greasing in order to avoid its corrosion in the future.

Heatwire greasing is not electrowire and serves for installation of electronic blocks of ignition from which intensive heat removal is required.

Hermetics

Anaerobny hermetic unlike RTV hermetic can be applied not only in addition to laying, but also to formation of those. Remains elastic, it is steady against influence of solvents and well fills roughnesses of surfaces. The main difference from RTV hermetic consists in hardening conditions. If RTV hermetic starts to stiffen after hit on air, anaerobny hermetic rises only in lack of air. It means that hardening of such hermetic occurs only after assembly a component and their dense pressing to each other.

Hermetic for pipes and carving connections is applied to sealing of shtutserny connections of hydraulic, pneumatic and vacuum lines. It is usually made on the basis of a teflon compound and it is delivered in the form of the aerosols put like paint of liquids or in the form of a tape (FUM).

Himikaly

The anti-taking compound serves for the prevention of "prikipaniye", corrosion, jamming and a cold privarivaniye of fixture. High-temperature anti-taking hermetics usually are made on the basis of medsoderzhashchy or graphite greasings and used in fixture of system of release and a final collector.

Taking compounds serve Anaerobnye for prevention of a spontaneous otdavaniye of fixture under the influence of vibrations and stiffen only after installation in absence of contact to air. Taking compounds of average capacity are applied to fixing of small fixture (nuts, bolts, screws) which are subject to a regular otdavaniye further. High-power compounds are usually used for blocking of the large fixture which otdavaniye is not made on a regular basis.

Additives to oil serve for change of chemical properties of oil without change of its viscosity for the purpose of decrease in an internal friction in the engine. It is necessary to notice that the majority of the firms manufacturers which are letting out engine oils, warn against use of any additives to them.

Additives to fuel carry out at once some functions, depending on the chemical composition. Usually contain the solvents promoting a conclusion of slags and removal of a deposit from internal surfaces and a component of system of injection of fuel and an inlet path. Besides, application of such additives promotes removal of the coal deposits which are forming on walls of chambers of combustion. The structure of some additives includes the substances serving for greasing a component of the top part of a head of cylinders (the klapanny mechanism, piston rings), others promote condensate removal from walls of a fuel tank.

The other

During car operation brake liquid takes away a certain quantity of water from air. Too big content of water in brake liquid can cause, finally, corrosion of details of working brake system. Besides, thus the temperature of boiling of brake liquid essentially goes down.

Therefore it is necessary to change time in two years brake liquid!

At very old brake liquid it is possible, at big load of working brake system, emergence of vials of steam in system. It negatively influences overall performance of working brake system and, thereby, on traffic safety.

It is necessary to apply only the recommended brake liquid.

Glue for fastening of sealing strips of body apertures as it is clear from its name, serves for fastening of sealing strips of apertures of doors, windows and covers of luggage compartments. It can be applied to fixing of elements of internal furnish.

Anticorrosive coverings for the bottom of the car are represented by the gudronoobrazny structure made on an oil basis, and serves for a sheeting of metal surfaces, preventing their corrosion. Besides, carries out function of sound insulation of salon.

Wax and polyrole are applied to protection of the painted surfaces against environment influences. Use of various type восков and polyroles can demand various type of paint. The structure of some polyroles includes the abrasive or chemical additives serving for removal of an external layer of oxides (tarnishing) from painted surfaces of old cars. Recently in the market are widely presented different polyroles not containing wax which structure includes a set of chemical additives, such as polymers or substances on a silicon basis. Such polyroles usually are put and keep more long than usual (wax) easier.